Datacap Logo

Download / NETePay Options / NETePay Classic – Processors / EVO Snap Host / NETePay EVO SNAP Host – ESH

NETePay EVO SNAP Host - ESH

Please follow the steps below to complete your installation of NETePay EVO SNAP Host – ESH

Step 1

Install Client Control

In order to communicate with this NETePay, your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.78

Release date: 06/13/2024

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our Compatible devices page.

Release notes for v1.78

  1. During an EMVParamDownload, the PinPadMfgSerialNo is now sent to the NETePay / Bridge.  Previously, only PinPadSerialNo was sent.  PIN pads loaded in distribution are tracked via the PinPadMfgSerialNo.  This value is sent to PSCS by the in-store NETePay/Bridge to register the PIN pad.  The logic to register a PIN pad with PSCS is in the NETePay Bridge version 5.08.52. 

  2. A new request field is supported for Hosted to allow an ISV to provide a specific tax amount if the card is surchargeable. The XML tag <TaxIfSurchargeable> is now passed through dsiEMVUS if included in a payment request. The amount sent in <Tax> to the MM NETePay depends if a card is surchargeable. If a card is surchargeable and a non-zero surcharge amount is included, then the Logic Engine will use the <TaxIfSurchargeable> for <Tax> rather than the value sent in <Tax>.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

OR

dsiPDCX® 1.93

Release date: 05/14/2024

Datacap’s ActiveX control for non-EMV transactions using NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers. dsiPDCX is included as part of the dsiEMVUS download, so this control only needs to be installed for non-EMV installs.

Release notes for v1.93

  • GetPrePaidStripe was fixed for the  ID Tech VP3300 and VP8300 devices.  Unsolicited display messages are now handled for these devices that do not have a display. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software. Generally, DISClientX should only be used for legacy installs.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Looking for an older version?

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.37

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 09/22/2021

  • Support is added for EVO SNAP host messaging version 2.1.36.  EVO fixed an issue for EMV chip card ZeroAuth transactions.

  • Support is added for Incremental Authorization and Partial Reversal transactions for credit cards.  One or more Incremental Auths may follow a PreAuth transaction.  This can be followed by a single Partial Reversal.  And finally, a PreAuthCapture is used to finalize the payment. 

  • An EMV brand certification was completed for PAX devices.  There is still a Visa Debit transaction to be run when EVO and FIS are ready. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.37 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.36

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 05/06/2021

During startup, if NETePay failed to pull parameters from PSCS, it should use its last set of parameters. In some cases, the Contactless Support parameter is set to “0” (Contactless MSD) rather than the last value pulled from PSCS. This is issue is corrected in this version.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.36 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.35

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 05/10/2021

  • EVO requires Datacap to obtain a Session Token which is used to authenticate each payment request. Previously, the Session Token was obtained every 30 minutes. Now the Session Token is obtained every 20 minutes.

  • A change is included to the “ApplicationConfigurationData” XML field to remove a “nil” string. The “nil” string was preventing the “ApplicationConfigurationData” fields from being processed by the EVO SNAP host.
  •  

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.35 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.34

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 04/27/2020

  • This version supports a single Service Key for all merchants. There is no longer a need to supply a Service Key value when boarding a merchant via PSCS.

  • EVO requires Datacap to obtain a Session Token every 30 to 45 minutes which is used to authenticate each payment request. EVO has provided an Identity Token (hard-coded in NETePay) that will expire in seven years. NETePay uses the Identity Token to request each Session Token. The Identity Token will need to be updated at some future date prior to its expiration. Previously, the Identity Token expired in three years.

  • Support is added for Ecommerce and MOTO merchant categories. Previously, only Retail and Restaurant categories were supported.

  • For previous versions, EVO returned a $0.00 Balance for all credit card transactions even though the card was not a prepaid or debit card. EVO has corrected this issue starting with this version.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.34 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.33

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 04/27/2020

  • This version supports a single Service Key for all merchants. There is no longer a need to supply a Service Key value when boarding a merchant via PSCS.
  • EVO requires Datacap to obtain a Session Token every 30 to 45 minutes which is used to authenticate each payment request. EVO has provided an Identity Token (hard-coded in NETePay) that will expire in seven years. NETePay uses the Identity Token to request each Session Token. The Identity Token will need to be updated at some future date prior to its expiration. Previously, the Identity Token expired in three years.
  • Support is added for Ecommerce and MOTO merchant categories. Previously, only Retail and Restaurant categories were supported.
  • For previous versions, EVO returned a $0.00 Balance for all credit card transactions even though the card was not a prepaid or debit card. EVO has corrected this issue starting with this version.
  •  

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.33 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay EVO SNAP Host - ESH 5.07.32

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 05/09/2019

  • Initial release of NETePay for EVO SNAP.
    • ID Tech Augusta with TDES encryption is certified for EMV on this platform. dsiPDCX and dsiEMVUS both support this device for EVO.
    • Support for typical EMV and non-EMV credit card integration with the Augusta.
    • Multi use tokens are supported.
    • SNAP does not current support Adjust or AdjustByRecordNo. They do have plans to support an Adjust this year.
    • This NETePay supports all of the optional features supported by other EMV NETePays such as Local Reporting and Store and Forward. Some features cannot be used at this point, like Pay at the Table, since that is no PIN pad supported. Debit and EBT will be supported in the next release with Ingenico devices.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay EVO SNAP Host – ESH 5.07.32 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 3

Install Administrative tools (optional)

Local Batch Report Viewer 1.03

Release date: 05/11/2020

Local Batch Report Viewer can be used to view the locally stored batch report of Host based NETePay who support support this feature and have it enabled via PSCS.

Release notes for v1.03

  • Fix for an issue which prevented errors from the open batch being shown in the decline/error tab.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

End-User License Agreement (EULA)

All Datacap software is provided ‘as-is’. Datacap makes no warranties, expressed or implied, as to merchantability or fitness for a particular purpose. Use of Datacap software is defined in an End-User License Agreement (EULA) included with each product and is presented for review during software installation.

To view the full EULA, click here.