Download / NETePay Options / NETePay Classic – Processors / Sterling-Chase / NETePay Sterling US EMV (CP) Host – PRH – Rental

NETePay Sterling US EMV (CP) Host - PRH - Rental

Please follow the steps below to complete your installation of NETePay Sterling US EMV (CP) Host – PRH – Rental

Step 1

Install Client Control

In order to communicate with this NETePay, your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.82

Release date: 02/11/2025

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our Compatible devices page.

Release notes for v1.82

  1. EMV EBT support is added for PAX attended devices, Ingenico Tetra devices and Verifone P200/P400/M400 devices.  EMV Support must be configured for “Credit and Debit” or “Credit and Debit Preferred” at the in-store NETePay / Bridge.  EMV EBT is supported only for Rapid Connect and Worldpay Core.  When the NETePay server apps complete QA, they will be released supporting EMV EBT.  This includes the NETePay Hosted Bridge, as well as In-store and MM NETePays for Rapid Connect and Worldpay Core.

  2. EMV configuration settings have been adjusted for the IDTech VP3350 supporting EMV L3 certifications for Worldpay Core and TSYS.  There is a change to support proper masking with the latest IDTech VP3350 firmware.

  3. For the Ingenico Self/3000, the contactless event delay is set to 0 during an EMVParamDownload.  Ingenico parameter 0008-0010.

  4. Card Data Collection now supports reading EBT cards (chip, swipe and tap).

  5. For PAX devices, cancel is now allowed from the POS for GetSignature.

  6. When using Linked Returns, the response tag <ReturnAmountRemaining> is now included in the XML response. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

OR

dsiPDCX® 1.96

Release date: 01/03/2025

Datacap’s ActiveX control for non-EMV transactions using NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers. dsiPDCX is included as part of the dsiEMVUS download, so this control only needs to be installed for non-EMV installs.

Release notes for v1.96

  1. Support is added for the Ingenico Lane/3600 for Worldpay IP following an EMV L3 certification.

  2. Support is added for a “whitelist” of card BINs to better identify cards that may be returned in the clear.  The whitelist is used for GetPrePaidStripe and GetPrePaidStripeAllTracks. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software. Generally, DISClientX should only be used for legacy installs.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Looking for a older version?

Step 2

Install NETePay Sterling US EMV (CP) Host - PRH 5.08.50 - Rental

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 02/21/2023

This version now supports the restaurant merchant category.  When the merchant category is set to “restaurant”, NETePay sends “Industry Data” that includes the gratuity amount and a server ID.  The server ID is the value sent in the OperatorID field on a transaction request.  The gratuity amount is always included in the overall transaction amount. 

Chase does not support TIP adjust.  PreAuth and PreAuthCapture are supported similar to First Data Rapid Connect for restaurant.  This version provides no changes to the integration.  The only change is to the host request message when the merchant category is set to restaurant. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

Or download NETePay Sterling US EMV (CP) Host – PRH 5.08.50 – Rental (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Contact Tech Support for a no-charge upgrade

Fill out the form below or contact Datacap Tech Support at 215-997-8989 x143 or support@dcap.com.

End-User License Agreement (EULA)

All Datacap software is provided ‘as-is’. Datacap makes no warranties, expressed or implied, as to merchantability or fitness for a particular purpose. Use of Datacap software is defined in an End-User License Agreement (EULA) included with each product and is presented for review during software installation.

To view the full EULA, click here.