Datacap Logo
Contact us
Datacap Logo

Download / Processor Options / NETePay Worldpay (MercuryPay) – MPH

NETePay Worldpay (MercuryPay) - MPH

Please follow the steps below to complete your installation of NETePay Worldpay (MercuryPay) – MPH

Step 1

Install Client Control

In order to communicate with this NETePay, your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.91

Release date: 02/05/2026

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our Compatible devices page.

Release notes for v1.91

  1. PAX A6630 devices were added. New SecureDevice values are below.

  2.   Ingenico Axium devices are added supporting Bluefin decryption on Hosted. New SecureDevice values are below.

  3. Ingenico Axium “Dim” settings are now set during an EMVParamDownload.  “arc/terminal/screen/dimTimeoutSec” = 300.  “arc/terminal/screen/lockTimeoutSec” = 0 

  4. For ID TECH devices, EMV tag 5F2D (language preference) is no longer converted after receiving the value from the device. The device sends the value as Hex ASCII which is exactly how it needs to be sent to payment services. This value is not sent to all payment services.  It is sent to TSYS.


New SecureDevice values:

EMV_A6630_PAYMENTECH
EMV_A6630_VANTIV_E2E
EMV_A6630_TSYS
EMV_A6630_TSYS_VOLT
EMV_A6630_RAPIDCONNECT
EMV_A6630_RAPIDCONNECT_E2E
EMV_A6630_HEARTLAND
EMV_A6630_DATACAP_E2E
EMV_A6630_DATACAP_BLUEFIN
EMV_DX4000_DATACAP_BLUEFIN
EMV_DX8000_DATACAP_BLUEFIN
EMV_EX6000_DATACAP_BLUEFIN
EMV_EX8000_DATACAP_BLUEFIN
EMV_RX5000_DATACAP_BLUEFIN
EMV_RX7000_DATACAP_BLUEFIN

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD DSIEMVUS (.exe)

OR

dsiPDCX® 2.00

Release date: 01/21/2026

Datacap’s ActiveX control for non-EMV transactions using NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers. dsiPDCX is included as part of the dsiEMVUS download, so this control only needs to be installed for non-EMV installs.

Release notes for v2.00

  1. Four new BINs are added to the whitelisted gift card BINs that dsiPDCX checks for GetPrePaidStripe and GetPrePaidStripeAllTracks.  dsiPDCX will not return clear card data unless the card BIN and card account length are allowed. The new BINs include 305720 (14 long), and 500015, 634120, 812900 (all 16 long).  There is a new PAX whitelist available that includes all of the new BINs.  There are also new whitelist files (SECBIN files) for Ingenico RBA, UPP and ARC. The Datacap Distribution Loader and Payloader are using these new whitelists. 

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD DSIPDCX (.exe)

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software. Generally, DISClientX should only be used for legacy installs.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD DSICLIENTX (.exe)
Looking for a older version?

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.07.33

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 08/23/2019

  • For the “EMV Support” parameter, the choice now includes “Debit Only”.
  • EMV Support is added for China Union Pay.
  • An EMV card brand certification was completed for Ingenico Tetra devices. These include the Lane/3000, 5000, 7000 and 8000. It also includes the Move/3500, Move/5000 and Link/2500. The latest client controls (dsiPDCX and dsiEMVUS) support these devices with TDES PAN encryption for Worldpay.
  • An EMV card brand certification was completed for the Ingenico Telium iUC285.
  • Support is added for a “VAS Gift – Apple Pass Type ID” which is used with the Verifone P400.
  • Support is added for BatchReportQuery and BatchReportTransaction TranCodes.

New build released 9/17/19 – Updated to SAF library 6.0. This fixes a critical stop error which can occur while forwarding without IP connectivity.

New build released 10/23/19 – Update to SAF library 7.0. This fixes a critical stop error which can occur where a forward contains a voided transaction with more than 1 child. This also corrects an issue where transactions may go online even though ForceOffline is set to “Y”.

New build released 11/4/19 – Update to SAF library 8.0. This fixes an issue where Authorize amounts over 999.99 may be formatted with commas.

New build released 1/17/20 – Local Batch Report library updated to v2.11. This corrects an issue where SAF transactions can fail after BatchReportTransaction is called.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETEPAY DIRECTOR (.exe)
User Guide

Or download NETePay Worldpay (MercuryPay) – MPH 5.07.33 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.07.31

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 01/16/2019

  • The following changes are made related to store and forward processing.
    • The SAF_ForwardAll operation will now recover if communication failures occur during the forwarding process. An error will be returned along with the number of transactions that have completed forwarding. A subsequent SAF_ForwardAll will pick up where the previous one left off.
    • If there are no transactions to forward, a SAF_ForwardAll operation will now return SUCCESS along with zero totals.
    • The SAF Totals now include a count of Uncaptured PreAuth requests. All PreAuth transactions should be captured prior to forwarding stored transactions. There is no way to be paid for a forwarded PreAuth that was not captured.
    • There is a purchase amount limit parameter set on PSCS and a purchase limit sent in from the POS. The smaller of the two is compared to the transaction purchase amount. If the transaction purchase amount is less than or equal to the smaller of the two limits, then the transaction can possibly be stored offline. Otherwise, the transaction will go online.
    • There is a maximum stored transaction limit set on PSCS and a stored transaction limit sent in from the POS. The smaller of the two is compared with the current number of stored transactions. If the addition of one more transaction would keep the number of stored transaction under or equal to the smaller of the two limits, then the transaction can possibly be stored offline. Otherwise, the transaction will go online.

  • For the “EMV Support” parameter, the choices now include …
    • None
    • Credit
    • Credit and Swiped PIN Debit
    • Credit and EMV Debit
    • Credit and Debit – Prefer Debit

  • This version also supports new parameters for contactless. The new parameters are …
    • “Contactless Support” – the choices are MSR or EMV.
    • “EMV Contactless CVM Limit (dollars)” – for EMV Contactless this amount will control whether or not a CVM is required. Over the amount some cardholder verification method is required.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETEPAY DIRECTOR (.exe)
User Guide

Or download NETePay Worldpay (MercuryPay) – MPH 5.07.31 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.07.30

NETePay Director

NETePay Director provides a simplified installation process with go-forward remote software updates.

Release date: 01/31/2018

  • Support added for NETePay 5 Director
  • For the “EMV Support” parameter, the choices now include.
    • None
    • Credit
    • Credit and Swiped PIN Debit
    • Credit and EMV Debit
  • When EMV is supported, the JCB AID is now loaded.
  • Support added for the following TranCodes.
    • EMVPreAuth
    • IncrementalAuthByRecordNo (requires at least dsiEMVUS v1.19 or dsiPDCX v1.51)
    • PartialReversalByRecordNo (requires at least dsiEMVUS v1.19 or dsiPDCX v1.51)

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETEPAY DIRECTOR (.exe)
User Guide

Or download NETePay Worldpay (MercuryPay) – MPH 5.07.30 (⚠ non-director installs do not support remote updates)

  • When applications are configured and running, the context menu now includes a new selection – Load Parameters (Stop/Start Director). The user can click one menu item to restart which will cause ePays to restart and reload parameters.
  • When a NETePay or GIFTePay window is opened, there are now four icons in the upper right corner that have the following functions.
    • View Merchant Parameters
    • PSCS
    • Email log
    • View log

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.07.20

NETePay Worldpay (MercuryPay) - MPH 5.07.20

Release date: 10/23/2017

  • PA-DSS 3.2
  • EMV Debit support is added for the following AIDs
    • A0000000033010 – Visa Interlink
    • A0000000980840 – Visa US Common Debit
    • A0000000042203 – US Maestro
    • A0000000043060 – Maestro
    • A0000001524010 – Discover US Common Debit
  • eWIC support is included in this version. This is an optional feature that must be enabled via PSCS and requires integration changes.
  • Store and Forward is added. This is an optional feature that must be enabled via PSCS and requires integration changes.
  • Pay At The Table is added. This is an optional feature that must be enabled via PSCS and requires integration changes.
  • Local Batch Reporting data storage is added. This is an optional feature that must be enabled via PSCS. Data can be viewed using the Local Batch Report Viewer.
  • Support for Auto-Updates.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETePay Worldpay (MercuryPay) - MPH 5.07.20 (.exe)
User Guide

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.06.11

NETePay Worldpay (MercuryPay) - MPH 5.06.11

Release date: 11/18/2015

Enhanced to support multiple card verification methods (CVMs).

  • Build 0001 released 1/13/17
    • Support for Smart Updates which allows NETePay to be automatically updated to its versions most currently build.
    • Support for being run as a service. Please review this NETePay’s userguide for details on configuring this feature.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETePay Worldpay (MercuryPay) - MPH 5.06.11 (.exe)
User Guide

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.06.10

NETePay Worldpay (MercuryPay) - MPH 5.06.10

Release date: 08/27/2015

Enhanced to support US EMV transactions utilizing the Verifone Vx805 PIN Pad. Point of Sale packages require Datacap’s dsiEMVUS™ control (US EMV) for proper functionality.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETePay Mercury US EMV - MPH 5.06.10 (.exe)
User Guide

Step 2

Install NETePay Worldpay (MercuryPay) - MPH 5.05.05

NETePay Worldpay (MercuryPay) - MPH 5.05.05

Release date: 06/18/2013

Validated at PA-DSS 2.0. POS Integrations utilizing Datacap’s dsiPDCX™ Out-of-Scope payments interface should install the “In-Store” version of NETePay for Mercury (formerly IPDial Bridge). This will maintain an Out-of-Scope environment.

Windows11 Pro / 10 Pro / Server 2019 / Server 2016

DOWNLOAD NETePay Worldpay (MercuryPay) - MPH 5.05.05 (.exe)
User Guide

End-User License Agreement (EULA)

All Datacap software is provided ‘as-is’. Datacap makes no warranties, expressed or implied, as to merchantability or fitness for a particular purpose. Use of Datacap software is defined in an End-User License Agreement (EULA) included with each product and is presented for review during software installation.

To view the full EULA, click here.

Go back
I Agree